MAX4618CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4618 |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 3.6V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Supply Current-Max (Isup) | 0.01mA |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 15pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 15ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Length | 19.175mm |
| RoHS Status | Non-RoHS Compliant |
MAX4618CPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Through Hole. 4:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of 0°C~70°C TA degrees Celsius. There are 16 terminations totally. A high-quality output is provided by the electrical component's 4 channels. When a voltage supply of 3.3V is used, the electronic component should be turned on and run. The electrical component body receives 16 pins. Circuits based on SP4T switching are used to construct these analog switch ics. There are 2 circuits in this switch device. Search with MAX4618 if you are looking for analog multiplexer variants. This switch device is a typical Multiplexer or Switches. Using a single voltage supply, this switch device consumes 2V~5.5V volts. With a DIFFERENTIAL MULTIPLEXER analog IC integrated into the board.
MAX4618CPE Features
4 Channels
Switch Circuit: SP4T
MAX4618CPE Applications
There are a lot of Maxim Integrated MAX4618CPE Analog Switches & Multiplexers ICs applications.
- Frame Relay Equipment
- Battery-powered systems
- Battery Powered Instruments
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Medical Instrumentation
- Digital cross connects (DSX-1)
- Cable Modem
- Modems
- Voice over IP/DSL – Integrated Access Devices, Smart
- ISDN NT1/TA
