MAX4618CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4618 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 20 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.01mA |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 15pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4618CSE+ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 4:1. Increasing operating temperature to around 0°C~70°C TA. In total, 16 terminations have occurred. A high-quality output is provided by the electrical component's 4 channels. Powered by a 3.3V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 16 series. The analog switch ics are built using SP4T switching circuits. It consists of 2 circuits. Use MAX4618 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 10Ohm. You can find the functions of the 16 pins in the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. A cost-effective Single supply type analogue multiplexer. There should be 2V voltage fed to the electrical part below 2V. The switch device would be able to operate with 1μA current. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. A voltage of 5V can be used to operate the electronic component.
MAX4618CSE+ Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4618CSE+ Applications
There are a lot of Maxim Integrated MAX4618CSE+ Analog Switches & Multiplexers ICs applications.
- Avionics
- Fiber In The Loop (FITL)
- High speed data transmission line cards
- PDAs
- Audio/video switches
- Industrial
- Microprocessor Controlled Analog Systems
- Microwave transmission systems
- Microprocessor controlled systems
- Routers
