MAX4618CSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4618 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 3.6V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Supply Current-Max (Isup) | 0.01mA |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 15pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 15ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
MAX4618CSE+T Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. It is mounted in the position Surface Mount. 4:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of 0°C~70°C TA degrees Celsius. There are 16 terminations totally. This electronic part offers high-quality output due to its 4 channels. An 3.3V voltage supply should allow the electrical part to be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. These analog multiplexers are built based on SP4T switching circuits. The circuits in this analogue multiplexer number 2. Try searching for MAX4618 variants of the analog switch ic. Multiplexer or Switches is a typical switch device. A voltage of 2V~5.5V is required to drain this analog switch from a single voltage supply. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board.
MAX4618CSE+T Features
4 Channels
Switch Circuit: SP4T
MAX4618CSE+T Applications
There are a lot of Maxim Integrated MAX4618CSE+T Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- PDH Multiplexers
- 65 V DACs
- FTTH
- Fault Tolerant Systems
- Industrial control systems
- Frame Relay Equipment
- Cable Modem
- Signal routing between systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
