MAX4618CUE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 533mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4618 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 20 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.01mA |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 15pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4618CUE+T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. 4:1 is the ratio of multiplexer to demultiplexer circuits. Around 0°C~70°C TA is the extended operating temperature. A total of 16 terminations have been recorded. The electronic part provides high-quality output because it has 4 channels. When a voltage supply of 3.3V is used, the electronic component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SP4T switching circuits. There are 2 circuits in this switch device. Try searching with MAX4618 if you're looking for variants. Analog switches have 10Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. It is recommended to use 2V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 1μA. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. There is a voltage range of 5V operating voltages for the electrical part.
MAX4618CUE+T Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4618CUE+T Applications
There are a lot of Maxim Integrated MAX4618CUE+T Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Medical
- ISDN NT1/TA
- Isolation
- Relay Replacement
- Industrial
- Channelized and Unchannelized DS3 applications
- Fiber In The Loop (FITL)
- Audio/video switches
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
