MAX4618EPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4618 |
| Pin Count | 16 |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Supply Current-Max (Isup) | 0.01mA |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 15pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 15ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4618EPE Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tube is used. In Through Hole, this analog switch is mounted. There is 4:1 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. In total, there have been 16 terminations. A 4 channel electronic part produces high-quality output. A 3.3V voltage supply should turn on and run the electronic component. It is part of the design of the 16 series that this electronic component is included. The analog switch ics are built using SP4T switching circuits. 2 circuits are used in this analogue multiplexer. Try searching with MAX4618 if you're looking for variants. There is 10Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A low voltage of 2V should be applied to the electronic component. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. It is integrated with a DIFFERENTIAL MULTIPLEXER analog IC.
MAX4618EPE Features
4 Channels
Switch Circuit: SP4T
MAX4618EPE Applications
There are a lot of Maxim Integrated MAX4618EPE Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- RGB switches
- Wireless Local Loop
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Communications systems
- ISDN NT1/TA
- Central office
- Intelligent PBX
- 65 V DACs
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
