MAX4618EUE
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Max Power Dissipation | 533mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4618 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 20 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.01mA |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 75mA |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 15pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Height | 950μm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX4618EUE Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tube is used. A switch device like this is mounted in Surface Mount. 4:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. In total, 16 terminations have occurred. A high-quality output is provided by the electrical component's 4 channels. When a voltage supply of 3.3V is used, the electronic component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. These analog multiplexers are built based on SP4T switching circuits. There are 2 circuits in this switch device. Try searching with MAX4618 to find analog multiplexer variants. A 10Ohm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. Multiplexers should not be powered above 5.5V in normal situations. A analog switch ic that has a cost-effective Single supply type. 2V should be the lowest voltage fed to the electronic component. 1μA current would be enough for this multiplexer to operate. Draining from a single voltage supply, this analog switch requires a voltage of 2V~5.5V. A voltage of 5V can be used to operate the electronic component.
MAX4618EUE Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4618EUE Applications
There are a lot of Maxim Integrated MAX4618EUE Analog Switches & Multiplexers ICs applications.
- Medical systems
- Audio and video switching
- Battery Powered Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Communications systems
- Power routing
- Sample hold systems
- Central office
- Frame Relay Equipment
- Signal routing between systems
