MAX4618EUE+T
| Parameters | |
|---|---|
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Max Power Dissipation | 533mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4618 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 20 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.01mA |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 75mA |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 15pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
MAX4618EUE+T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 4:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. There are 16 terminations totally. A high-quality output is provided by the electrical component's 4 channels. An 3.3V voltage supply should allow the electrical part to be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SP4T switching circuits. A total of 2 circuits make up this switch device. Use MAX4618 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 10Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analog switch ics with Single supply type are cost-effective. The lowest voltage the electronic part should receive is 2V. The analogue multiplexer could operate on 1μA current. This analogue multiplexer requires a voltage of 2V~5.5V when it drains from a single voltage supply. 5V operating voltages are supported by the electronic component.
MAX4618EUE+T Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4618EUE+T Applications
There are a lot of Maxim Integrated MAX4618EUE+T Analog Switches & Multiplexers ICs applications.
- Communications systems
- Sample-and-hold systems
- Communication systems
- SDH
- High reliability control systems
- DSLAMs
- Cable Modem
- Data Acquisition Systems
- Automatic test equipment
- E1 Multiplexer
