banner_page

MAX4619CPE+

15ns, 10ns SPDT 10Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4619 16 Pins 1nA 3.3V 16-DIP (0.300, 7.62mm)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX4619CPE+
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 172
  • Description: 15ns, 10ns SPDT 10Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4619 16 Pins 1nA 3.3V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Through Hole
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Number of Pins 16
Operating Temperature 0°C~70°C TA
Packaging Tube
Published 2011
JESD-609 Code e0
Pbfree Code no
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 10Ohm
Terminal Finish Tin/Lead (Sn85Pb15)
Max Power Dissipation 842mW
Technology CMOS
Terminal Position DUAL
Peak Reflow Temperature (Cel) 240
Number of Functions 3
Supply Voltage 3.3V
Terminal Pitch 2.54mm
Time@Peak Reflow Temperature-Max (s) 20
Base Part Number MAX4619
Pin Count 16
Power Supplies 2.5/5V
Number of Channels 1
Interface Logic
Number of Circuits 3
Max Supply Voltage 5.5V
Min Supply Voltage 2V
Operating Supply Current 1μA
Propagation Delay 20 ns
Turn On Delay Time 15 ns
Logic Function Multiplexer
Supply Type Single
Supply Current-Max (Isup) 0.01mA
Turn-Off Delay Time 10 ns
On-State Resistance (Max) 10Ohm
Multiplexer/Demultiplexer Circuit 2:1
Current - Leakage (IS(off)) (Max) 1nA
Channel Capacitance (CS(off), CD(off)) 5pF 8.5pF
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 15ns, 10ns
Charge Injection 3pC
Channel-to-Channel Matching (ΔRon) 200m Ω
Crosstalk -96dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 2V~5.5V
Drain to Source Resistance 10Ohm
Signal Current-Max 0.075A
Height Seated (Max) 4.572mm
Length 19.175mm
Width 7.62mm
Radiation Hardening No
REACH SVHC Unknown
RoHS Status ROHS3 Compliant
Lead Free Lead Free

MAX4619CPE+ Overview


Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. Mounted in Through Hole is this multiplexer. There is 2:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around 0°C~70°C TA. There are 16 terminations totally. High-quality output is provided by the electronic component's 1 channels. When a voltage supply of 3.3V is used, the electronic component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SPDT switching circuits. 3 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with MAX4619. An switch multiplexer with 10Ohm internal resistance has a value of 10Ohm. For details about the functions of 16 pins, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. A cost-effective Single supply type analogue multiplexer. 2V should be the lowest voltage fed to the electronic component. In order to operate this switch device, it would need a current of 1μA. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. There is 10Ohm Drain to Source resistance on this electronic part.

MAX4619CPE+ Features


1 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 10Ohm

MAX4619CPE+ Applications


There are a lot of Maxim Integrated MAX4619CPE+ Analog Switches & Multiplexers ICs applications.

  • PBXs
  • Battery Powered Instruments
  • Existing multiplexer applications (both fault-protected and nonfault-protected)
  • Microprocessor Controlled Analog Systems
  • Automotive applications
  • RGB switches
  • Switching Systems
  • PDH Multiplexers
  • Cable Modem
  • Low-Voltage

Write a review

Note: HTML is not translated!
    Bad           Good