MAX4619CSE
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 3 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4619 |
| Pin Count | 16 |
| Operating Supply Voltage | 3.3V |
| Power Supplies | 2.5/5V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 10μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 20 ns |
| Supply Current-Max (Isup) | 0.01mA |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 8.5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX4619CSE Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tube provides high reliability. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operation at a temperature around 0°C~70°C TA. There are 16 terminations totally. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 3.3V volts, the electrical component should be turned on and run. As part of its design, the 16 series is equipped with this electronic component. Based on SPDT switching circuits, these analog multiplexers work. The circuits in this analogue multiplexer number 3. Search with MAX4619 if you are looking for analog multiplexer variants. An switch multiplexer with 10Ohm internal resistance has a value of 10Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 5.5V in normal situations. It is recommended to use 2V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 10μA. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. 3.3V operating voltages are supported by the electronic component.
MAX4619CSE Features
1 Channels
Switch Circuit: SPDT
10μA Supply Current
MAX4619CSE Applications
There are a lot of Maxim Integrated MAX4619CSE Analog Switches & Multiplexers ICs applications.
- Frame Relay Equipment
- New designs requiring multiplexer functions
- Voice over IP/DSL – Integrated Access Devices, Smart
- Microprocessor Controlled Analog Systems
- Private Branch Exchange (PBX)
- SONET
- DVD-R
- PCMCIA cards
- Sample-and-hold systems
- Cross Connects
