MAX4619CUE+T
| Parameters | |
|---|---|
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 533mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4619 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 20 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.01mA |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 8.5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
MAX4619CUE+T Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. The advanced packaging method Tape & Reel (TR) provides high reliability. This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. The operating temperature is extended to around 0°C~70°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. A 3.3V voltage supply should turn on and run the electronic component. An injection of 16 pins is performed into the body of the electrical component. A SPDT switching circuit is used to build these analog multiplexers. This multiplexer is composed of 3 circuits. Try searching for the analog switch ic with MAX4619 if you are looking for variants. As far as internal resistance is concerned, it has 10Ohm. Please refer to the datasheets for 16 pins functions. normally, users should not supply switches with voltages higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. For this digital switch to work, 1μA current would suffice. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. This electrical part is compatible with 5V operating voltages.
MAX4619CUE+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4619CUE+T Applications
There are a lot of Maxim Integrated MAX4619CUE+T Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- CSU
- PBXs
- HDTV
- Power routing
- PBX interfaces
- Video switching
- Remote wireless modules
- Microprocessor Controlled Analog Systems
- Fault Tolerant Systems
