Parameters |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Weight |
172.98879mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2000 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
10Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
533mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
3 |
Supply Voltage |
3.3V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4619 |
Pin Count |
16 |
Operating Supply Voltage |
5V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Propagation Delay |
15 ns |
Turn On Delay Time |
15 ns |
Supply Type |
Single |
Turn-Off Delay Time |
10 ns |
On-State Resistance (Max) |
10Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
5pF 8.5pF |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
15ns, 10ns |
Charge Injection |
3pC |
Channel-to-Channel Matching (ΔRon) |
200m Ω |
Crosstalk |
-96dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
20ns |
Voltage - Supply, Single (V+) |
2V~5.5V |
Signal Current-Max |
0.075A |
Height |
900μm |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mounting Type |
Surface Mount |
MAX4619EUE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tube. In Surface Mount, you'll find this switch device. 2:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~85°C TA. In total, there have been 16 terminations. A 1 channel electronic part produces high-quality output. Powered by a 3.3V voltage supply, the electrical part should be switched on and run. There is an electrical component included in the 16 series. The analog switch ics are built using SPDT switching circuits. The circuits in this analogue multiplexer number 3. If you are looking for variants of the digital switch, trying search with MAX4619. It has an internal resistance of 10Ohm. Please refer to the datasheets for 16 pins functions. It is a typical Multiplexer or Switches analog multiplexer. normally, users should not supply switches with voltages higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 2V. This multiplexer would work with 1μA current. Draining from a single voltage supply, this analog switch requires a voltage of 2V~5.5V. Putting voltage greater than 1μA on the multiplexer may cause damage. A voltage of 5V can be used to operate the electronic component.
MAX4619EUE+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4619EUE+ Applications
There are a lot of Maxim Integrated MAX4619EUE+ Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- Avionics test equipment
- Switching Systems
- Microprocessor Controlled Analog Systems
- Digital Cross-Connects
- Microprocessor controlled systems
- E1 Network Equipment
- Communications systems
- Relay Replacement
- Isolation