MAX4620EPD+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Base Part Number | MAX4620 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Nominal Supply Current | 10μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 250 ns |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 8.5pF |
| On-state Resistance Match-Nom | 0.6Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 300ns |
| Switch-off Time-Max | 150ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Length | 19.05mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4620EPD+ Overview
The electrical component comes in 14-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. In Through Hole, this analog switch is mounted. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. In total, there have been 14 terminations. The electronic part provides high-quality output because it has 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 14 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. This multiplexer is composed of 4 circuits. Try searching for MAX4620 variants of the analog switch ic. An switch multiplexer with 70Ohm internal resistance has a value of 70Ohm. The functions of 14 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 12V voltage to the switch device. An effective Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 2V. This analog switch requires a voltage of 2V~12V to drain from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. 9V operating voltages can be used with this electrical part.
MAX4620EPD+ Features
1 Channels
Switch Circuit: SPST - NO
MAX4620EPD+ Applications
There are a lot of Maxim Integrated MAX4620EPD+ Analog Switches & Multiplexers ICs applications.
- Transmit
- Fiber to the Home
- Cable PC
- Signal routing between systems
- PDH Multiplexers
- Fault Tolerant Systems
- Precision data acquisition
- Multi-Line E1 Interface Cards
- Audio and video switching
- USB 1.1 signal switching circuits
