MAX4620EUD+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4620 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 250 ns |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 8.5pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4620EUD+T Overview
Shipping overseas is convenient with the electronic component packed in 14-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. A total of 14 terminations have been recorded. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. Into the electrical component body are injected 14 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. The circuits in this analogue multiplexer number 4. Search with MAX4620 if you are looking for analog multiplexer variants. A 70Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 14 pins are available. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analogue multiplexers of the Single supply type that are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer could operate on 1μA current. This analog switch requires a voltage of 2V~12V to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating voltages of 9V are compatible with the electrical part.
MAX4620EUD+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4620EUD+T Applications
There are a lot of Maxim Integrated MAX4620EUD+T Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Microwave transmission systems
- Microprocessor Controlled Analog Systems
- Industrial and process control systems
- Cable Modem
- Modems
- Data Acquisition Systems
- 65 V DACs
- Avionics and Military Systems
- Low-Voltage
