Parameters |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
5Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4623 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Number of Channels |
2 |
Number of Circuits |
2 |
Max Supply Voltage |
20V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
1nA |
Max Supply Current |
500nA |
Throw Configuration |
DPST |
Turn On Delay Time |
250 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~18V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
5Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
62 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
34pF 34pF |
On-state Resistance Match-Nom |
0.25Ohm |
Switch Circuit |
DPST - NO |
Switch Time (Ton, Toff) (Max) |
250ns, 200ns |
Charge Injection |
480pC |
Channel-to-Channel Matching (ΔRon) |
250m Ω |
Crosstalk |
-60dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Length |
19.175mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4623CPE Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. To ensure high reliability, a new packaging method Tube is used. A switch device like this is mounted in Through Hole. Multiplexer and demultiplexer circuits have a number 2:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. Totally, there are 16 terminations. The electronic part provides high-quality output because it has 2 channels. An 15V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 16 pins. DPST - NO switching circuits are used in these analog switch ics. There are 2 circuits in this switch device. MAX4623 can be used to search for analog multiplexer variants. A 5Ohm internal resistance characterizes this multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 20V to a switch device. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 4.5V. Putting voltage greater than 500nA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. There are SEPARATE OUTPUT outputs on this analog switch ic.
MAX4623CPE Features
2 Channels
Switch Circuit: DPST - NO
MAX4623CPE Applications
There are a lot of Maxim Integrated MAX4623CPE Analog Switches & Multiplexers ICs applications.
- Power routing
- Channelized and Unchannelized DS3 applications
- T1/E1 Terminals
- PDAs
- USB 1.1 signal switching circuits
- Multi-Line E1 Interface Cards
- Battery Powered Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Microprocessor Controlled Analog Systems
- Fiber In The Loop (FITL)