MAX4626EUK-T
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4626 |
| Pin Count | 5 |
| JESD-30 Code | R-PDSO-G5 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| On-State Resistance (Max) | 500mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 51 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 65pF 65pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 50ns, 30ns |
| Charge Injection | 40pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 500mOhm |
| Normal Position | NO |
| Length | 2.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4626EUK-T Overview
Shipping overseas is convenient with the electronic component packed in SC-74A, SOT-753. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 5. The electronic part provides high-quality output because it has 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. There is an electrical component included in the 5 series. A SPST - NO switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with MAX4626. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. The Drain to Source resistance of this electronic component is 500mOhm.
MAX4626EUK-T Features
1 Channels
Switch Circuit: SPST - NO
Drain-to-Source resistance: 500mOhm
MAX4626EUK-T Applications
There are a lot of Maxim Integrated MAX4626EUK-T Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- Battery-powered systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Optical Applications
- 65 V DACs
- Industrial control systems
- Medical systems
- PDH Multiplexers
- Medical Instrumentation
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
