Parameters |
Off-state Isolation-Nom |
51 dB |
Current - Leakage (IS(off)) (Max) |
2nA |
Channel Capacitance (CS(off), CD(off)) |
65pF 65pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
50ns, 30ns |
Charge Injection |
40pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
90ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Drain to Source Resistance |
500mOhm |
Normal Position |
NO |
Height |
1.1mm |
Length |
2.9mm |
Width |
1.63mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
SC-74A, SOT-753 |
Number of Pins |
5 |
Weight |
29.993795mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2000 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Resistance |
500mOhm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
571mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4626 |
Pin Count |
5 |
Operating Supply Voltage |
5V |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
10μA |
Nominal Supply Current |
10μA |
Max Supply Current |
10μA |
Throw Configuration |
SPST |
Turn On Delay Time |
50 ns |
Supply Type |
Single |
Turn-Off Delay Time |
30 ns |
On-State Resistance (Max) |
500mOhm |
Multiplexer/Demultiplexer Circuit |
1:1 |
MAX4626EUK+T Overview
Due to its SC-74A, SOT-753 packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. 5 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 5 pins. The analog switch ics are built using SPST - NO switching circuits. Look for analog switch ic variants by searching with MAX4626. A 500mOhm internal resistance characterizes this multiplexer. To find out what the functions of 5 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The digital multiplexer has a low cost Single supply. There should be 1.8V voltage fed to the electrical part below 1.8V. In order to operate this switch device, it would need a current of 10μA. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 10μA. 5V operating voltages can be used with this electrical part. It has a Drain to Source resistance of 500mOhm ohms.
MAX4626EUK+T Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
Drain-to-Source resistance: 500mOhm
MAX4626EUK+T Applications
There are a lot of Maxim Integrated MAX4626EUK+T Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Communications systems
- Data Acquisition Systems
- Microprocessor controlled systems
- MP3 players
- Fault Tolerant Systems
- Industrial and process control systems
- Optical Applications
- Residential Gateways, Home Gateway/Router
- Avionics and Military Systems