MAX4631EPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4631 |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 230μA |
| Max Supply Current | 325μA |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 18pF 18pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 500ns |
| Switch-off Time-Max | 400ns |
| Normal Position | NO |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4631EPE Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. The advanced packaging method Tube provides high reliability. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. This electronic part can be found in the 16 series. Unlike digital switches, these are based on SPST - NO switching circuits. This multiplexer is composed of 2 circuits. Try searching with MAX4631 to find analog multiplexer variants. A 85Ohm internal resistance characterizes this multiplexer. The functions of 16 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. It is recommended that the electrical component receives a voltage of 9V. A digital multiplexer may suffer damage if voltage is applied above 325μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 18V. In the case of dual power supplies, you should connect at least 4.5V. This electrical part is compatible with 18V operating voltages.
MAX4631EPE Features
1 Channels
Switch Circuit: SPST - NO
MAX4631EPE Applications
There are a lot of Maxim Integrated MAX4631EPE Analog Switches & Multiplexers ICs applications.
- PDAs
- Automotive applications
- Optical Applications
- Modems
- Avionics test equipment
- Cable Modem
- Data Acquisition Systems
- Private Branch Exchange (PBX)
- Video switching
- Ultrasound
