MAX4633ESE
| Parameters | |
|---|---|
| Throw Configuration | DPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 18pF 18pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 500ns |
| Switch-off Time-Max | 400ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4633 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 230μA |
| Max Supply Current | 325μA |
MAX4633ESE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Surface Mount, you'll find this switch device. 2:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. The total number of terminations is 16. High-quality output is provided by the electronic component's 2 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. There is an electrical component included in the 16 series. These analog multiplexers are built based on DPST - NO switching circuits. A 2 circuit is present in this switch device. Try searching with MAX4633 to find analog multiplexer variants. It has an internal resistance of 85Ohm. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended to use 9V as the lowest voltage for the electrical part. Putting voltage greater than 325μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 18V. The voltage should be at least 4.5V if you are using dual power supplies. The electrical part can be operated at 15V voltage levels.
MAX4633ESE Features
2 Channels
Switch Circuit: DPST - NO
MAX4633ESE Applications
There are a lot of Maxim Integrated MAX4633ESE Analog Switches & Multiplexers ICs applications.
- Power routing
- Routers
- Precision instrumentation
- Channel Banks
- Low-Voltage
- High speed data transmission line cards
- 65 V DACs
- PCMCIA cards
- RGB switches
- Cable Modem
