MAX4635EUB+T

14ns, 6ns SPDT 4Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4635 10 Pins 100pA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4635EUB+T
Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 872
Description: 14ns, 6ns SPDT 4Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4635 10 Pins 100pA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Number of Pins	10
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2003
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
ECCN Code	EAR99
Resistance	5.5Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	330mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4635
Output	SEPARATE OUTPUT
Pin Count	10
Operating Supply Voltage	5V
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Turn On Delay Time	8 ns
Supply Type	Single
Turn-Off Delay Time	18 ns
On-State Resistance (Max)	4Ohm
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	52 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	9pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	14ns, 6ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	100m Ω
Crosstalk	-67dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	1.8V~5.5V
Height Seated (Max)	1.1mm
Length	3mm
Width	3mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant

MAX4635EUB+T Overview

Packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. In total, 10 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. An injection of 10 pins is performed into the body of the electrical component. A SPDT switching circuit is used for these analog switches. Circuits number 2 make up this analogue multiplexer. MAX4635 can be used to search for analog multiplexer variants. The internal resistance of this digital multiplexer is 5.5Ohm. For details about the functions of 10 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analogue multiplexers of the Single supply type that are cost-effective. There should be 1.8V voltage fed to the electrical part below 1.8V. The analogue multiplexer could operate on 1μA current. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. A voltage of 5V can be used to operate the electronic component.