Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2003 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
4Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
330mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4636 |
Pin Count |
10 |
Power Supplies |
3/5V |
Number of Channels |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Turn On Delay Time |
14 ns |
Supply Type |
Single |
Turn-Off Delay Time |
6 ns |
On-State Resistance (Max) |
4Ohm |
High Level Output Current |
30mA |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
52 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
14ns, 6ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-67dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
18ns |
Switch-off Time-Max |
8ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Height |
950μm |
Length |
3.05mm |
Width |
3.05mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX4636EUB+ Overview
Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. There are 10 terminations totally. The electronic part provides high-quality output because it has 2 channels. A 3V voltage supply should turn on and run the electronic component. It is part of the design of the 10 series that this electronic component is included. A SPDT switching circuit is used for these analog switches. Try searching with MAX4636 to find analog multiplexer variants. An switch multiplexer with 4Ohm internal resistance has a value of 4Ohm. The datasheets for the 10 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. The digital multiplexer has a low cost Single supply. 1.8V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1μA current. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. It may damage the digital multiplexer if the voltage is higher than 1μA.
MAX4636EUB+ Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4636EUB+ Applications
There are a lot of Maxim Integrated MAX4636EUB+ Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Private Branch Exchange (PBX)
- Audio and video routing
- Imaging
- FTTH
- Transmit
- Communications systems
- CSU
- Microwave transmission systems
- Multiplexers