Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2003 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
4Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
330mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4636 |
Pin Count |
10 |
Power Supplies |
3/5V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1nA |
Max Supply Current |
1nA |
Turn On Delay Time |
14 ns |
Supply Type |
Single |
Turn-Off Delay Time |
6 ns |
On-State Resistance (Max) |
4Ohm |
High Level Output Current |
30mA |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
52 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
14ns, 6ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-67dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
18ns |
Switch-off Time-Max |
8ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4636EUB+T Overview
Due to its 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 2:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 10. As a result of its 1 channels, this electronic component provides high-quality output. A 3V voltage supply should turn on and run the electronic component. A total of 10 pins are injected into the body of the electronic part. Multiplexers built on a SPDT switching circuit are built. The multiplexer consists of 2 circuits. MAX4636 can be used to search for analog multiplexer variants. This digital multiplexer has 4Ohm internal resistance. The datasheets for the 10 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 1.8V. It would be sufficient to run this analogue multiplexer with 1μA current. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. When the digital multiplexer is charged above 1nA, damage can occur.
MAX4636EUB+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4636EUB+T Applications
There are a lot of Maxim Integrated MAX4636EUB+T Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Industrial and process control systems
- Microwave transmission systems
- 65 V DACs
- E1 Multiplexer
- ATM
- PDH Multiplexers
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Communications systems
- Precision instrumentation