MAX4642EUA+TG104
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 4Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4642 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 7pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 15ns, 8ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -97dB @ 1MHz |
| Switch-off Time-Max | 10ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4642EUA+TG104 Overview
Presented in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 1:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 8. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. A key feature of the 8 series is the inclusion of this electronic part as part of its design. A SPST - NC switching circuit is used to build these analog multiplexers. There are 2 circuits in this switch device. Try searching for MAX4642 variants of the analog switch ic. As far as internal resistance is concerned, it has 4Ohm. Datasheets for 8 pin functions are available upon request. A voltage higher than 5.5V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. 1.8V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 1μA would be sufficient for this switch device. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V.
MAX4642EUA+TG104 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX4642EUA+TG104 Applications
There are a lot of Maxim Integrated MAX4642EUA+TG104 Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- Data Acquisition Systems
- Optical Applications
- New designs requiring multiplexer functions
- Cable PC
- Relay Replacement
- CSU
- PBX interfaces
- Cross Connects
- Avionics
