Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2002 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
4Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
362mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4643 |
Output |
SEPARATE OUTPUT |
Pin Count |
8 |
Operating Supply Voltage |
5V |
Number of Channels |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1nA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
10 ns |
Supply Type |
Single |
Turn-Off Delay Time |
20 ns |
On-State Resistance (Max) |
4Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
80 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
7pF 7pF |
On-state Resistance Match-Nom |
0.2Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
15ns, 8ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
200m Ω |
Crosstalk |
-97dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4643EUA Overview
Presented in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tube. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. There are 8 terminations totally. The electronic part delivers high-quality output through its 2 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. The electrical component body receives 8 pins. A SPST - NO/NC switching circuit is used for these analog switches. Look for analog switch ic variants by searching with MAX4643. An switch multiplexer with 4Ohm internal resistance has a value of 4Ohm. The datasheets for the 8 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. 1.8V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 1nA. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. It can operate from 5V operating voltages.
MAX4643EUA Features
2 Channels
Switch Circuit: SPST - NO/NC
1nA Supply Current
MAX4643EUA Applications
There are a lot of Maxim Integrated MAX4643EUA Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- Channel Banks
- Digital cross connects (DSX-1)
- DSUs
- High speed data transmission line cards
- Medical systems
- HDTV
- New designs requiring multiplexer functions
- Channelized and Unchannelized DS3 applications
- Battery Powered Systems