Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
SC-74A, SOT-753 |
Number of Pins |
5 |
Weight |
29.993795mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2004 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
Resistance |
2.5Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
571mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
3V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4645 |
Pin Count |
5 |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
100pA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
15 ns |
Supply Type |
Single |
Turn-Off Delay Time |
10 ns |
On-State Resistance (Max) |
2.5Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
55 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
17pF 17pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
15ns, 10ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5V |
Normal Position |
NO |
Height |
1.3mm |
Length |
3mm |
Width |
1.75mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4645EUK-T Overview
Shipping overseas is convenient with the electronic component packed in SC-74A, SOT-753. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. 5 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. It is part of the design of the 5 series that this electronic component is included. Based on SPST - NO switching circuits, these analog multiplexers work. Look for analog switch ic variants by searching with MAX4645. The internal resistance of this digital multiplexer is 2.5Ohm. You can find the functions of the 5 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. An effective Single supply digital multiplexer. A low voltage of 1.8V should be applied to the electronic component. For this digital switch to work, 100pA current would suffice. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5V. A voltage higher than 1μA may cause damage to the switch multiplexer.
MAX4645EUK-T Features
1 Channels
Switch Circuit: SPST - NO
100pA Supply Current
MAX4645EUK-T Applications
There are a lot of Maxim Integrated MAX4645EUK-T Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- Sample-and-hold systems
- Avionics
- Cross Connects
- Microprocessor Controlled Analog Systems
- Audio and video signal routing
- Multi-Line E1 Interface Cards
- Cell phones
- Relay Replacement
- FTTH