Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
SC-74A, SOT-753 |
Number of Pins |
5 |
Weight |
29.993795mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2004 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Resistance |
2.5Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
571mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
3V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4646 |
Pin Count |
5 |
Operating Supply Voltage |
5V |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
100pA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
10 ns |
Supply Type |
Single |
Turn-Off Delay Time |
10 ns |
On-State Resistance (Max) |
2.5Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
55 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
17pF 17pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
15ns, 10ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5V |
Normal Position |
NC |
Length |
2.9mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4646EUK-T Overview
The electronic part can be shipped overseas conveniently because it is packaged in SC-74A, SOT-753. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 5. High-quality output is provided by the electronic component's 1 channels. A 3V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 5 series. These analog multiplexers are built based on SPST - NC switching circuits. The circuits in this analogue multiplexer number 1. Try searching for MAX4646 variants of the analog switch ic. A 2.5Ohm internal resistance characterizes this multiplexer. Datasheets for 5 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. The digital multiplexer has a low cost Single supply. There should be 1.8V voltage fed to the electrical part below 1.8V. The analogue multiplexer could operate on 100pA current. This analog switch requires a voltage of 1.8V~5V to drain from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. There is a voltage range of 5V operating voltages for the electrical part.
MAX4646EUK-T Features
1 Channels
Switch Circuit: SPST - NC
100pA Supply Current
MAX4646EUK-T Applications
There are a lot of Maxim Integrated MAX4646EUK-T Analog Switches & Multiplexers ICs applications.
- SDH
- Residential Gateways, Home Gateway/Router
- SONET
- 65 V DACs
- Microprocessor controlled systems
- Channelized and Unchannelized DS3 applications
- Battery Powered Instruments
- Modems
- Industrial control systems
- PDAs