MAX4652EUE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 7Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 457mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4652 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 10 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 16 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 16pF 16pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Height | 950μm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX4652EUE+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tube is used to provide high reliability. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operational temperature extended around -40°C~85°C TA. In total, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. A 3V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 16 series. Multiplexers built on a SPST - NO switching circuit are built. There are 4 circuits in this multiplexer. Try searching with MAX4652 to find analog multiplexer variants. This digital multiplexer has 7Ohm internal resistance. The datasheets for the 16 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. There should be 1.8V voltage fed to the electrical part below 1.8V. It would be sufficient to run this analogue multiplexer with 1μA current. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. The electronic component can function from 5V.
MAX4652EUE+ Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4652EUE+ Applications
There are a lot of Maxim Integrated MAX4652EUE+ Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Sample hold systems
- DSLAMs
- Communications systems
- Microprocessor Controlled Analog Systems
- PBX interfaces
- Wireless Local Loop
- Access Concentrators
- Avionics
- ATM
