MAX4655ESA+
| Parameters | |
|---|---|
| Nominal Supply Current | 150μA |
| Max Supply Current | 150μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 125 ns |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 20V |
| -3db Bandwidth | 210MHz |
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 77 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 25pF 25pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 23pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.509W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX4655 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
MAX4655ESA+ Overview
The electronic component is convenient to ship overseas because it is packed in a 8-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. In total, 8 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. This electrical component is included in the 8 series of products. On the other hand, analog switches can be constructed using SPST - NC switching circuits. A 1 circuit is present in this switch device. If you are looking for variants of the digital switch, trying search with MAX4655. In this multiplexer, the internal resistance is 10Ohm. Datasheets for 8 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 40V to the switch device in normal circumstances. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 9V. If you put voltage higher than 150μA on the digital multiplexer, damage may occur. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 4.5V should be attached. 20V operating voltages are supported by the electronic component.
MAX4655ESA+ Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 210MHz
MAX4655ESA+ Applications
There are a lot of Maxim Integrated MAX4655ESA+ Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- Low-Voltage
- Modems
- Fault Tolerant Systems
- Medical Instrumentation
- Avionics
- Frame Relay Equipment
- Precision test equipment
- High speed data transmission line cards
- Existing multiplexer applications (both fault-protected and nonfault-protected)
