MAX4656ESA+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX4656 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 90μA |
| Max Supply Current | 150μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| -3db Bandwidth | 210MHz |
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 77 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 25pF 25pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 23pC |
| Switch-on Time-Max | 200ns |
| Normal Position | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4656ESA+T Overview
The electronic component is convenient to ship overseas because it is packed in a 8-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. There are 8 terminations totally. By its 1 channels, the electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 8 series that this electronic component is included. The analog switch ics are built using SPST - NO switching circuits. 1 circuits are used in this analogue multiplexer. MAX4656 can be used to search for analog multiplexer variants. Analog switches have 10Ohm internal resistance. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 40V. Analog switch ics with Dual, Single supply type are cost-effective. 9V should be the lowest voltage fed to the electronic component. If you put voltage higher than 150μA on the digital multiplexer, damage may occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. A dual power supply should have at least 4.5V voltage attached. 20V operating voltages can be used with this electrical part.
MAX4656ESA+T Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 210MHz
MAX4656ESA+T Applications
There are a lot of Maxim Integrated MAX4656ESA+T Analog Switches & Multiplexers ICs applications.
- Medical
- Fiber In The Loop (FITL)
- Intelligent PBX
- SONET
- Modems
- Medical Instrumentation
- Cellular phones
- PCMCIA cards
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Public switching systems
