MAX4656EUA+

200ns, 100ns SPST - NO 10Ohm Analog Switches MAX4656 8 Pins 1nA 15V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4656EUA+
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 374
Description: 200ns, 100ns SPST - NO 10Ohm Analog Switches MAX4656 8 Pins 1nA 15V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)(Kg)

Details

Tags

Parameters
Packaging	Tube
Published	2007
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Resistance	10Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	362mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4656
Pin Count	8
Operating Supply Voltage	20V
Number of Channels	1
Number of Circuits	1
Max Supply Voltage	40V
Min Supply Voltage	9V
Nominal Supply Current	90μA
Max Supply Current	150μA
Throw Configuration	SPST
Turn On Delay Time	300 ns
Voltage - Supply, Single/Dual (±)	9V~40V ±4.5V~20V
Supply Type	Dual, Single
Bandwidth	210MHz
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	150 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	10Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	77 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	25pF 25pF
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	200ns, 100ns
Charge Injection	23pC
Switch-on Time-Max	200ns
Drain to Source Resistance	10Ohm
Normal Position	NO
Height	950μm
Length	3.05mm
Width	3.05mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Number of Pins	8
Operating Temperature	-40°C~85°C TA

MAX4656EUA+ Overview

Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 8 terminations. By its 1 channels, the electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. This electrical component is included in the 8 series of products. The analog switch ics are built using SPST - NO switching circuits. A 1 circuit is present in this switch device. Try searching for the analog switch ic with MAX4656 if you are looking for variants. As far as internal resistance is concerned, it has 10Ohm. The functions of 8 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 40V in normal situations. An effective Dual, Single supply digital multiplexer. 9V should be the lowest voltage fed to the electronic component. If put voltage greater than 150μA on the device, damage may be caused to the analogue multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. For dual power supplies, a voltage of at least 4.5V should be attached. There is a voltage range of 20V operating voltages for the electrical part. 210MHz bandwidths enable data to be transferred. The Drain to Source resistance of this electronic component is 10Ohm.