MAX4657EUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 362mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4657 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 90μA |
| Max Supply Current | 150μA |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 125 ns |
| Max Dual Supply Voltage | 20V |
| -3db Bandwidth | 210MHz |
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 77 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 25pF 25pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 23pC |
| Normal Position | NC |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4657EUA+T Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. There are 8 terminations totally. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. An injection of 8 pins is performed into the body of the electrical component. These analog multiplexers are built based on SPST - NC switching circuits. There are 1 circuits in this multiplexer. Try searching with MAX4657 to find analog multiplexer variants. Analog switches have 10Ohm internal resistance. Please refer to the datasheets for 8 pins functions. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 40V to a switch device. The lowest voltage fed to the electronic component should be 9V. Putting voltage greater than 150μA on the multiplexer may cause damage. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. It is recommended that you attach at least 4.5V to your dual power supply. There is a voltage range of 18V operating voltages for the electrical part.
MAX4657EUA+T Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 210MHz
MAX4657EUA+T Applications
There are a lot of Maxim Integrated MAX4657EUA+T Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Avionics
- Frame Relay Equipment
- Low-Voltage
- Precision test equipment
- Channelized and Unchannelized DS3 applications
- PBXs
- Relay replacements
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Microprocessor controlled systems
