MAX4659EUA+

SPDT 25Ohm Analog Switches BREAK-BEFORE-MAKE MAX4659 8 Pins 1nA 15V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4659EUA+
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Datasheet: PDF
Stock: 665
Description: SPDT 25Ohm Analog Switches BREAK-BEFORE-MAKE MAX4659 8 Pins 1nA 15V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Number of Pins	8
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2007
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Termination	SMD/SMT
ECCN Code	EAR99
Resistance	25Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	362mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4659
Pin Count	8
Operating Supply Voltage	20V
Polarity	Non-Inverting
Number of Channels	1
Number of Circuits	1
Max Supply Voltage	40V
Min Supply Voltage	9V
Nominal Supply Current	135μA
Max Supply Current	135μA
Turn On Delay Time	85 ns
Voltage - Supply, Single/Dual (±)	9V~40V ±4.5V~20V
Supply Type	Dual, Single
Bandwidth	225MHz
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	85 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	25Ohm
Min Dual Supply Voltage	4.5V
High Level Output Current	75mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	70 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	6pF
On-state Resistance Match-Nom	0.4Ohm
Switch Circuit	SPDT
Charge Injection	1.5pC
Channel-to-Channel Matching (ΔRon)	400m Ω
Crosstalk	-76dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	25Ohm
Height	950μm
Length	3.1mm
Width	3.1mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant

MAX4659EUA+ Overview

Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 8 terminations. The electronic part delivers high-quality output through its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the body of the electronic part. The analog switch ics are built using SPDT switching circuits. A 1 circuit is present in this switch device. Look for analog switch ic variants by searching with MAX4659. It has an internal resistance of 25Ohm. For details about the functions of 8 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 40V in normal situations. A cost-effective Dual, Single supply type analogue multiplexer. A low voltage of 9V should be applied to the electronic component. If put voltage greater than 135μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. The electronic component can function from 20V. 225MHz bandwidths enable data to be transferred. A Drain to Source resistance of 25Ohm is shown for this electronic part.