MAX4660EUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 25Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.509W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4660 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| JESD-30 Code | S-PDSO-G8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 200μA |
| Max Supply Current | 135μA |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| -3db Bandwidth | 225MHz |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -76dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4660EUA+T Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. In total, 8 terminations have occurred. A 1 channel electronic part produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. A total of 8 pins are injected into the body of the electronic part. A SPDT switching circuit is used to build these analog multiplexers. A total of 1 circuits make up this switch device. If you are looking for variants of the digital switch, trying search with MAX4660. As far as internal resistance is concerned, it has 25Ohm. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 40V. Analog switch ics with Dual, Single supply type are cost-effective. 9V is the lowest voltage that should be fed to the electronic electronic part. Put voltage above 135μA on the multiplexer to cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. There are SEPARATE OUTPUT outputs on this analog switch ic. It can operate from 20V operating voltages.
MAX4660EUA+T Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 225MHz
MAX4660EUA+T Applications
There are a lot of Maxim Integrated MAX4660EUA+T Analog Switches & Multiplexers ICs applications.
- Routers
- DSLAMs
- Cellular phones
- PDAs
- Relay replacements
- Access Concentrators
- Cell phones
- ISDN NT1/TA
- Industrial and process control systems
- DSUs
