Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.209, 5.30mm Width) |
Number of Pins |
16 |
Weight |
130.010913mg |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
2.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
571mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4661 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Number of Channels |
4 |
Max Supply Voltage |
36V |
Min Supply Voltage |
4.5V |
Max Supply Current |
500nA |
Throw Configuration |
SPST |
Turn On Delay Time |
275 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
175 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
2.5Ohm |
Min Dual Supply Voltage |
4.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
56 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
55pF 55pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
275ns, 175ns |
Charge Injection |
300pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-59dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
2.5Ohm |
Normal Position |
NO |
Height |
1.78mm |
Length |
6.33mm |
Width |
5.38mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX4661CAE+ Overview
Presented in 16-SSOP (0.209, 5.30mm Width), this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tube. This analog switch is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operational temperature extended around 0°C~70°C TA. There are 16 terminations totally. Due to its 4 channels, the electrical component produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 16 series that this electronic component is included. These analog multiplexers are built based on SPST - NC switching circuits. Look for analog switch ic variants by searching with MAX4661. As far as internal resistance is concerned, it has 2.5Ohm. For functions related to 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. normally, users should not supply switches with voltages higher than 36V. A analog switch ic that has a cost-effective Dual, Single supply type. There should be 4.5V voltage fed to the electrical part below 4.5V. A voltage higher than 500nA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIf you are using dual power supplies, you should attach at least 4.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Drain to Source resistance for this electronic component is 2.5Ohm.
MAX4661CAE+ Features
4 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 2.5Ohm
MAX4661CAE+ Applications
There are a lot of Maxim Integrated MAX4661CAE+ Analog Switches & Multiplexers ICs applications.
- DSUs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- SONET/SDH ADM
- Medical
- Frame Relay Equipment
- Wireless Local Loop
- PBXs
- Intelligent PBX
- Battery-powered systems
- Avionics and Military Systems