Parameters |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
2.5Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4661 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
20V |
Power Supplies |
12/+-15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
36V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
5μA |
Max Supply Current |
500nA |
Throw Configuration |
SPST |
Turn On Delay Time |
250 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
400 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
2.5Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
56 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
55pF 55pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
275ns, 175ns |
Charge Injection |
300pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-59dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
275ns |
Switch-off Time-Max |
175ns |
Normal Position |
NO |
Length |
19.175mm |
Width |
7.62mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4661CPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tube is used. This analog switch is mounted in Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around 0°C~70°C TA are extended for operation. Total terminations are 16. Due to its 1 channels, the electrical component produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. These analog multiplexers are built based on SPST - NC switching circuits. A 4 circuit is present in this switch device. If you are looking for variants of the digital switch, trying search with MAX4661. It has an internal resistance of 2.5Ohm. The datasheets for the 16 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 36V. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage fed to the electronic component should be 4.5V. When the digital multiplexer is charged above 500nA, damage can occur. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. A dual power supply should have at least 4.5V voltage attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating voltages of 20V are compatible with the electrical part.
MAX4661CPE Features
1 Channels
Switch Circuit: SPST - NC
MAX4661CPE Applications
There are a lot of Maxim Integrated MAX4661CPE Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Avionics and Military Systems
- Channelized and Unchannelized DS3 applications
- Audio signal routing
- PCMCIA cards
- DSLAMs
- Communications systems
- Communication systems
- Imaging
- Microprocessor Controlled Analog Systems