MAX4661EAE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Weight | 130.010913mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4661 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 275 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 175 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 300pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height | 1.78mm |
| Length | 6.33mm |
| Width | 5.38mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4661EAE Overview
The electrical component comes in 16-SSOP (0.209, 5.30mm Width) packaging, which makes it convenient to ship overseas. The advanced packaging method Tube provides high reliability. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. In total, there are 16 terminations. This electronic part offers high-quality output due to its 4 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. Electronic part bodies are injected with 16 pins. Multiplexers built on a SPST - NC switching circuit are built. Try searching for the analog switch ic with MAX4661 if you are looking for variants. An switch multiplexer with 2.5Ohm internal resistance has a value of 2.5Ohm. The datasheets for the 16 pins explain the functions. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage fed to the electronic component should be 4.5V. It may damage the digital multiplexer if the voltage is higher than 500nA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VYou should attach at least 4.5V voltage if you are using dual power supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
MAX4661EAE Features
4 Channels
Switch Circuit: SPST - NC
MAX4661EAE Applications
There are a lot of Maxim Integrated MAX4661EAE Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- High-Voltage
- Low-Voltage
- PDH Multiplexers
- Remote wireless modules
- Medical systems
- Digital access cross connects
- Power routing
- Relay Replacement
- Audio and video signal routing
