MAX4661EPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4661 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 300pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 175ns |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4661EPE Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. A 1 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. An injection of 16 pins is performed into the body of the electrical component. These analog multiplexers are built based on SPST - NC switching circuits. This multiplexer is composed of 4 circuits. Try searching for MAX4661 variants of the analog switch ic. An switch multiplexer with 2.5Ohm internal resistance has a value of 2.5Ohm. For details about the functions of 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 36V. It is recommended to use 4.5V as the lowest voltage for the electrical part. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4661EPE Features
1 Channels
Switch Circuit: SPST - NC
MAX4661EPE Applications
There are a lot of Maxim Integrated MAX4661EPE Analog Switches & Multiplexers ICs applications.
- Medical
- Precision instrumentation
- Modems
- Audio and video switching
- SDH
- Relay replacements
- Precision data acquisition
- Communications systems
- Multi-Line E1 Interface Cards
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
