MAX4662CAE
| Parameters | |
|---|---|
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 300pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 175ns |
| Normal Position | NC |
| Height | 1.78mm |
| Length | 6.33mm |
| Width | 5.38mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
MAX4662CAE Overview
As the electronic part is packed in 16-SSOP (0.209, 5.30mm Width), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tube. In Surface Mount, this analog switch is mounted. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around 0°C~70°C TA is the extended operating temperature. 16 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. The analog switch ics are built using SPST - NO switching circuits. The multiplexer consists of 4 circuits. An switch multiplexer with 4Ohm internal resistance has a value of 4Ohm. Datasheets for 16 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 36V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 4.5V. If you put voltage higher than 500nA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. With dual power supplies, you should attach at least 4.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. 20V operating voltages can be used with this electrical part.
MAX4662CAE Features
1 Channels
Switch Circuit: SPST - NO
MAX4662CAE Applications
There are a lot of Maxim Integrated MAX4662CAE Analog Switches & Multiplexers ICs applications.
- Medical
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Remote Powered Equipment
- Video signal routing
- Microwave transmission systems
- DSUs
- Access Concentrators
- Medical systems
- Remote wireless modules
- Industrial
