Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.209, 5.30mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
1999 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
2.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
571mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4662 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
20V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
36V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
5μA |
Max Supply Current |
500nA |
Throw Configuration |
SPST |
Turn On Delay Time |
250 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
175 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
2.5Ohm |
Min Dual Supply Voltage |
4.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
56 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
55pF 55pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
275ns, 175ns |
Charge Injection |
300pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-59dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
275ns |
Normal Position |
NC |
Height Seated (Max) |
1.99mm |
Length |
6.2mm |
Width |
5.29mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4662EAE+T Overview
Presented in 16-SSOP (0.209, 5.30mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, there are 16 terminations. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. The electrical component body receives 16 pins. A SPST - NO switching circuit is used for these analog switches. The circuits in this analogue multiplexer number 4. Search with MAX4662 if you are looking for analog multiplexer variants. It has an internal resistance of 2.5Ohm. For functions related to 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 4.5V. Put voltage above 500nA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. Operating voltages of 20V are compatible with the electrical part.
MAX4662EAE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX4662EAE+T Applications
There are a lot of Maxim Integrated MAX4662EAE+T Analog Switches & Multiplexers ICs applications.
- Routers
- CSU
- Power routing
- Microprocessor Controlled Analog Systems
- Avionics
- Switching Systems
- Industrial and process control systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Cell phones
- DVD-R