MAX4662EPE
| Parameters | |
|---|---|
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 200mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 300pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 175ns |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Power Supplies | 12/+-15V |
MAX4662EPE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). In order to provide high reliability, an advanced packaging method Tube is used. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. In total, 16 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the body of the electronic part. Based on SPST - NO switching circuits, these analog multiplexers work. It consists of 4 circuits. The datasheets for the 16 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. 4.5V is the lowest voltage the electrical component should receive. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 4.5V.
MAX4662EPE Features
1 Channels
Switch Circuit: SPST - NO
MAX4662EPE Applications
There are a lot of Maxim Integrated MAX4662EPE Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Modems
- SONET/SDH ADM
- Medical Instrumentation
- Microprocessor Controlled Analog Systems
- DSLAMs
- DVD-R
- E1 Multiplexer
- PDH Multiplexers
- Routers
