MAX4663EPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4663 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 300pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 175ns |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4663EPE Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. Multiplexers like this are mounted in the Through Hole position. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. There are 16 terminations totally. A 1 channel electronic part produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 16 pins are injected into the electrical part body. Unlike digital switches, these are based on SPST - NO/NC switching circuits. 4 circuits are used in this analogue multiplexer. Try searching for the analog switch ic with MAX4663 if you are looking for variants. This digital multiplexer has 2.5Ohm internal resistance. Datasheets for functions of 16 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 36V to a switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended to use 4.5V as the lowest voltage for the electrical part. Put voltage above 500nA on the multiplexer to cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. A dual power supply should have at least 4.5V voltage attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. There is a voltage range of 20V operating voltages for the electrical part.
MAX4663EPE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4663EPE Applications
There are a lot of Maxim Integrated MAX4663EPE Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Battery-powered systems
- Access Concentrators
- CSU
- Data Acquisition Systems
- Industrial
- HDTV
- Transmit
- Audio and video signal routing
- Industrial control systems
