MAX4664CPE
| Parameters | |
|---|---|
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 4Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 34pF 34pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 300pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -60dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 175ns |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4664 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
MAX4664CPE Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tube. Mounted in Through Hole is this multiplexer. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature extended to 0°C~70°C TA. In total, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An injection of 16 pins is performed into the body of the electrical component. SPST - NC switching circuits are used in these analog switch ics. 4 circuits are used in this analogue multiplexer. Using the MAX4664 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 4Ohm. The functions of 16 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 36V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 4.5V is the lowest voltage the electrical component should receive. When the digital multiplexer is charged above 500nA, damage can occur. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 4.5V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. The electronic component can function from 20V.
MAX4664CPE Features
1 Channels
Switch Circuit: SPST - NC
MAX4664CPE Applications
There are a lot of Maxim Integrated MAX4664CPE Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- Avionics and Military Systems
- Microprocessor controlled systems
- Fiber In The Loop (FITL)
- Digital access cross connects
- High-Voltage
- Data switching
- High reliability control systems
- Intelligent PBX
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
