MAX4665EPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4665 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 4Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 34pF 34pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 300pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -60dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 175ns |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4665EPE Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Operational temperature extended around -40°C~85°C TA. 16 terminations have been made so far. This electronic part offers high-quality output due to its 1 channels. A 15V voltage supply should turn on and run the electronic component. There are 16 pins injected into the electronic part body. Circuits based on SPST - NO switching are used to construct these analog switch ics. There are 4 circuits in this switch device. Try searching with MAX4665 to find analog multiplexer variants. An switch multiplexer with 4Ohm internal resistance has a value of 4Ohm. The functions of 16 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 36V. 4.5V should be the lowest voltage fed to the electronic component. For this switch, a dual supply voltage is feasible, but it must not exceed 20VFor dual power supplies, a voltage of at least 4.5V should be attached. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX4665EPE Features
1 Channels
Switch Circuit: SPST - NO
MAX4665EPE Applications
There are a lot of Maxim Integrated MAX4665EPE Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Data Acquisition Systems
- Signal routing between systems
- CSU
- Relay Replacement
- Public switching systems
- Audio and video routing
- Remote wireless modules
- PBXs
- Medical systems
