MAX4666CPE

275ns, 175ns SPST - NO/NC 4Ohm Analog Switches BREAK-BEFORE-MAKE MAX4666 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4666CPE
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 674
Description: 275ns, 175ns SPST - NO/NC 4Ohm Analog Switches BREAK-BEFORE-MAKE MAX4666 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Operating Temperature	0°C~70°C TA
Packaging	Tube
Published	1999
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	4Ohm
Terminal Finish	Tin/Lead (Sn85Pb15)
Subcategory	Multiplexer or Switches
Max Power Dissipation	696mW
Technology	CMOS
Peak Reflow Temperature (Cel)	240
Number of Functions	4
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	MAX4666
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	20V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	36V
Min Supply Voltage	4.5V
Operating Supply Current	1nA
Nominal Supply Current	5μA
Max Supply Current	500nA
Throw Configuration	SPST
Turn On Delay Time	250 ns
Voltage - Supply, Single/Dual (±)	4.5V~36V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	400 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	4Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	62 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	34pF 34pF
On-state Resistance Match-Nom	0.2Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	275ns, 175ns
Charge Injection	300pC
Channel-to-Channel Matching (ΔRon)	200m Ω
Crosstalk	-60dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	275ns
Switch-off Time-Max	175ns
Length	19.175mm
Width	7.62mm
Radiation Hardening	No
RoHS Status	Non-RoHS Compliant

MAX4666CPE Overview

The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. It is mounted in the position Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around 0°C~70°C TA. 16 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. These analog multiplexers are built based on SPST - NO/NC switching circuits. It consists of 4 circuits. Try searching for MAX4666 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 4Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 36V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. It is recommended to use 4.5V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1nA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 500nA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. A voltage of 20V can be used to operate the electronic component.