MAX4666ESE
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4666 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 4Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 34pF 34pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 300pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -60dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 175ns |
| Height | 2.35mm |
| Length | 10.5mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4666ESE Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tube is used to provide high reliability. A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. A electrical component with 4 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. There are 16 pins injected into the electronic part body. A SPST - NO/NC switching circuit is used for these analog switches. Try searching for MAX4666 variants of the analog switch ic. In this multiplexer, the internal resistance is 4Ohm. Datasheets for 16 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. There should be 4.5V voltage fed to the electrical part below 4.5V. The analogue multiplexer may be damaged if voltage is greater than 500nA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIf you are using a dual power supply, you should attach at least 4.5V. 20V operating voltages can be used with this electrical part.
MAX4666ESE Features
4 Channels
Switch Circuit: SPST - NO/NC
MAX4666ESE Applications
There are a lot of Maxim Integrated MAX4666ESE Analog Switches & Multiplexers ICs applications.
- HDTV
- RGB switches
- Low-Voltage
- Multi-Line E1 Interface Cards
- Battery-powered systems
- Transmit
- High reliability control systems
- PDAs
- PCMCIA cards
- Isolation
