MAX4668CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | MAX4668 |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 275 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 175 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 65pF 65pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 450pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -66dB @ 1MHz |
| Switch-on Time-Max | 400ns |
| Switch-off Time-Max | 300ns |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4668CPE+ Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around 0°C~70°C TA extended. Total terminations are 16. The electronic part delivers high-quality output through its 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Circuits based on SPST - NO switching are used to construct these analog switch ics. There are 2 circuits in this switch device. Search with MAX4668 if you are looking for analog multiplexer variants. An switch multiplexer with 2.5Ohm internal resistance has a value of 2.5Ohm. The functions of 16 pins can be found in the datasheets. Users should never supply a voltage higher than 20V to a switch device. Analog switch ics with Dual, Single supply type are cost-effective. There should be 4.5V voltage fed to the electrical part below 4.5V. If you put voltage higher than 500nA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply.
MAX4668CPE+ Features
1 Channels
Switch Circuit: SPST - NO
MAX4668CPE+ Applications
There are a lot of Maxim Integrated MAX4668CPE+ Analog Switches & Multiplexers ICs applications.
- Central office
- Fiber to the Home
- ISDN NT1/TA
- Intelligent PBX
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- PBXs
- Communication systems
- PCMCIA cards
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Avionics test equipment
