MAX4668EPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4668 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 65pF 65pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 450pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 300ns |
| Normal Position | NC |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4668EPE Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. In Through Hole, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. It is injected into the electrical part body with 16 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Circuits number 2 make up this analogue multiplexer. Search with MAX4668 if you are looking for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 2.5Ohm. Please refer to the datasheets for 16 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. Multiplexers should not be powered above 36V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. 4.5V is the lowest voltage the electrical component should receive. A digital multiplexer may suffer damage if voltage is applied above 500nA. Despite this switch device's dual supply capability, its voltage should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. There are SEPARATE OUTPUT outputs on this analog switch ic. 18V operating voltages are supported by the electronic component.
MAX4668EPE Features
1 Channels
Switch Circuit: SPST - NO
MAX4668EPE Applications
There are a lot of Maxim Integrated MAX4668EPE Analog Switches & Multiplexers ICs applications.
- Automotive applications
- Cross Connects
- Cellular phones
- Battery Powered Instruments
- Medical
- SDH/SONET multiplexers
- Switching Systems
- USB 1.1 signal switching circuits
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Avionics test equipment
