Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
2.5Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4668 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
20V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
1nA |
Max Supply Current |
500nA |
Throw Configuration |
SPST |
Turn On Delay Time |
275 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
175 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
2.5Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
65pF 65pF |
On-state Resistance Match-Nom |
0.05Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
275ns, 175ns |
Charge Injection |
450pC |
Channel-to-Channel Matching (ΔRon) |
50m Ω |
Crosstalk |
-66dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
400ns |
Switch-off Time-Max |
300ns |
Normal Position |
NC |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4668ESE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. 16 terminations have been made so far. This electronic part offers high-quality output due to its 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. An electrical component of this type can be found in the 16 series. The analog switch ics are built using SPST - NO switching circuits. Circuits number 2 make up this analogue multiplexer. If you are looking for variants of the digital switch, trying search with MAX4668. This digital multiplexer has 2.5Ohm internal resistance. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 20V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended to use 4.5V as the lowest voltage for the electrical part. If put voltage greater than 500nA on the device, damage may be caused to the analogue multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
MAX4668ESE Features
1 Channels
Switch Circuit: SPST - NO
MAX4668ESE Applications
There are a lot of Maxim Integrated MAX4668ESE Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Access Concentrators
- Battery Powered Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Industrial and process control systems
- Automatic test equipment
- Cellular phones
- CSU
- 65 V DACs
- PBX interfaces