MAX4668ESE+T
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 2.5Ohm |
| Terminal Finish | TIN |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | MAX4668 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 65pF 65pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 450pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -66dB @ 1MHz |
| Switch-off Time-Max | 175ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4668ESE+T Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. 16 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. A 15V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 16 pins. A SPST - NO switching circuit is used for these analog switches. There are 2 circuits in this multiplexer. Search with MAX4668 if you are looking for analog multiplexer variants. It has an internal resistance of 2.5Ohm. In normalcircumstances, users should not exceed 36V volts for the multiplexer. In order for the electronic part to function properly, the lowest voltage should be 4.5V. Put voltage above 500nA on the multiplexer to cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. 18V operating voltages are supported by the electronic component.
MAX4668ESE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX4668ESE+T Applications
There are a lot of Maxim Integrated MAX4668ESE+T Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Central office
- Industrial
- Public switching systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cable PC
- Isolation
- Industrial control systems
- SONET/SDH ADM
- Intelligent PBX
