MAX4669CSE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4669 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 275 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 175 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 65pF 65pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 450pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Switch-off Time-Max | 300ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
MAX4669CSE Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around 0°C~70°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. There are 16 pins injected into the electronic part body. The analog switch ics are built using SPST - NO/NC switching circuits. Circuits number 2 make up this analogue multiplexer. Try searching with MAX4669 to find analog multiplexer variants. A 2.5Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 16 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 20V to a switch device. Dual, Single supply type digital switch with a low cost. 4.5V is the lowest voltage that should be fed to the electronic electronic part. A voltage higher than 500nA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 20VA dual power supply should have at least 4.5V voltage attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
MAX4669CSE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4669CSE Applications
There are a lot of Maxim Integrated MAX4669CSE Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Communication systems
- SDH/SONET multiplexers
- Relay replacements
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- T1/E1 Terminals
- Channel Banks
- RGB switches
- Precision test equipment
- Battery Powered Systems
