MAX4674EEE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Additional Feature | CAN ALSO OPERATE WITH 5V SUPPLY |
| Max Power Dissipation | 667mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4674 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Turn On Delay Time | 22 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.001mA |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 20pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 18ns, 6ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 150m Ω |
| Crosstalk | -114dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.73mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4674EEE+T Overview
Packed in 16-SSOP (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Temperatures around -40°C~85°C TA are extended for operation. 16 terminations have been made so far. As a result of its 2 channels, this electronic component provides high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the body of the electronic part. These analog multiplexers are built based on SPDT switching circuits. There are 4 circuits in this multiplexer. Look for analog switch ic variants by searching with MAX4674. As far as internal resistance is concerned, it has 4Ohm. You can find the functions of the 16 pins in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. There should be 1.8V voltage fed to the electrical part below 1.8V. In order to operate this switch device, it would need a current of 1μA. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. The electrical part can be operated at 5V voltage levels. There is also CAN ALSO OPERATE WITH 5V SUPPLY to look out for in this electronic part.
MAX4674EEE+T Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
Additional Features: CAN ALSO OPERATE WITH 5V SUPPLY
MAX4674EEE+T Applications
There are a lot of Maxim Integrated MAX4674EEE+T Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Battery Powered Instruments
- SDH/SONET multiplexers
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Avionics test equipment
- Avionics and Military Systems
- ATM
- High speed data transmission line cards
- T1/E1 Terminals
- Microprocessor Controlled Analog Systems
